Use a trailerable PWC cover to protect your jet ski on the road.

When it comes to trailering your jet ski, a trailerable PWC cover can help protect your boat, keep it dry, and prevent road grime or gravel from marring your boat’s finish. Below are some tips on securing your trailerable cover for highway travel.

• Only use a trailerable cover to protect your PWC on the road. Do not use a storage cover that is not approved for trailering use.
• Make sure the PWC cover is installed tightly. Follow the manufacturer’s instructions for installing your cover. All trailering straps should be attached and tied down tightly.
• Make sure the gas tank door is zipped shut.
• Secure any loose strap ends. If the straps are left to flap in the wind, they can cause damage to the cover or to your PWC.
• Before driving, recheck all straps.
• After driving for a few miles, stop and check all the straps again. Tighten straps as needed to make sure the PWC and cover are secure. If you are trailering the PWC for a long distance, check the PWC and trailering straps every time you stop for gas or food.

DuraShield Covers is now carrying PWC jet ski covers by Classic Accessories. Whether you are trailering your jet ski to the lake or storing it over winter, you’ll get all the protection you need with these heavy-duty jet ski covers. Both types of Classic Accessories covers are water-repellent to keep your PWC dry on the road and at home.

Classic Accessories PWC Jet Ski Cover

Classic Accessories PWC Jet Ski Cover (2 sizes available)

Keep your PWC looking fresh and playing strong with WaveGear™ marine canvas. Whether you are trailering your jet ski to the lake or storing it over winter, you’ll get all the protection you need with Classic Accessories Trailerable PWC Covers.

The water-repellent fabric keeps your PWC dry in wet conditions, and an elastic bottom hem and tie downs hold your cover in place during storage and trailering.

Available in 2 sizes:

• Jet skis up to 124″
• Jet skis over 124″

Features:

• Rope attaches to rugged non-scratch D-rings—no grommets to pull out or scratch
• Storage strap and tie-down rope included
• Elastic cord sewn into bottom hem for a fast, snug fit
• Water repellent fabric
• Integrated trailering strap
• Two year warranty
• Fits one, two, and three-person watercrafts up to 124″ long
• Gray color

Deluxe Classic Accessories PWC Jet Ski Cover

Deluxe Classic Accessories PWC Jet Ski Cover (2 sizes available)

Keep your PWC looking fresh and playing strong with UV and mildew resistant ProtekX™ Plus fabric. Whether you are trailering your jet ski to the lake or storing it over winter, you’ll get all the protection you need with Classic Accessories Deluxe Trailerable PWC Covers.

This heavy-duty travel cover comes with an integrated trailering system for quick loading and securing. Tension panels tightly secure the cover for highway travel. Rear air vents let moisture escape and prevent wind lofting. A zippered fuel tank provides easy access on both sides for fueling up on the road.

Available in 2 sizes:

• Jet skis up to 124″
• Jet skis over 124″

Features:

• Integrated trailering system with built-in quick adjusting straps
• Rear air vents reduce inside moisture and wind lofting
• Zippered fuel tank access door on both sides
• Integrated storage bag
• Elastic cord hem for a fast, tight fit
• Tension panels tightly secure cover for highway travel
• Quick-adjusting side-release strap buckles
• Built-in strap keepers secure excess strap after tightening
• Tough UV and mildew resistant ProtekX™ Plus fabric for maximum protection against sun, rain, dirt and pollutants
• Three year warranty
• Fits two and three-person watercrafts over 124″ long
• Black color

A jet ski cover protects your PWC from the elements.

Jet ski covers are an easy and inexpensive way to protect your boat from exposure to the elements, both for trailering and storage.

Trailering

When you are trailering your jet ski, road grime, mud, and dirt can get on your boat. These abrasive elements wear away at your boat’s finish. To protect your PWC on the road, use a trailerable jet ski cover. Make sure the cover is installed properly and tied down tightly before trailering. Stop every so often to check the tie downs. Retighten as necessary.

Storage

Whether you store your jet ski indoors or outside, a jet ski cover can keep your boat dry and clean. If you store your jet ski outdoors, a cover can protect against damage from UV rays, rain, snow, salt, sand and grit, dirt, and dust. Your jet ski will last longer and stay in better condition if you protect it with a cover.

Even if you store your jet ski in a garage or shed, you’ll still need a PWC cover to prevent dust and dirt buildup. Make sure the cover is equipped with adequate ventilation to allow moisture and condensation to evaporate.

Before covering your jet ski, make sure it is completely dry. Moisture trapped underneath the cover can damage your boat.

A PWC cover will protect your jet ski from the elements.

When it comes to keeping your jet ski clean, covered, and protected from the weather, a PWC cover is just what you need. With your jet ski snug under its cover, it will be protected from just about anything nature can throw at it. Here are a few tips on installing the PWC cover from DuraShield Covers:

1. Before you place your cover over the PWC, make sure you cover any sharp edges or points on the PWC with a cloth or fabric barrier. This will help to prevent tears or other damage to the cover.
a
2. To install the cover, first find the sewn-in tag that says “front.” Install the front of the cover over the nose of the PWC and gently pull the cover over the remaining length of the PWC, making sure to pull it tight below the rub rail.
a
3. Secure the cover by using the front and rear click-fit straps, along with the center seat cinch strap.
a
4. Adjust the security straps to the desired fit.

Now your PWC is covered and ready for storage!

This jet ski cover includes a venting system to allow air circulation.

To keep your jet ski in top shape, it’s important to protect it with a jet ski cover. Finding the right jet ski cover is as simple as knowing what type of cover you need and measuring your jet ski. Follow the steps below to find the best jet ski cover for your needs.

1. Decide whether you need a trailerable cover or a regular storage cover.

Trailerable covers can be used for storage and for trailering on an open trailer. They are often made with thicker material, fit tightly, and come with tie down straps to keep the cover in place. Storage covers are not approved for trailering but are designed to protect your jet ski from sun and weather damage.

Your cover should include a built-in venting system. Vents allow air to circulate underneath the cover, preventing moisture damage and discouraging the growth of mold and mildew. A venting system also reduces lofting, where the wind billows underneath the cover. Too much wind tearing at your jet ski cover can rip it apart in no time.

2. Measure your jet ski.

To find the correct measurements for your jet ski, measure the centerline length straight from the bow to the stern. Do not measure up and over any components of the jet ski.

Next, measure the beam (the flat width of the boat at its widest point). This is usually located near the middle of the jet ski.

3. Use these measurements to find the right size jet ski cover.

Using a sizing chart or the measurements listed for each cover, find the right size for your jet ski. If your jet ski is between two sizes, choose the larger size to ensure a proper fit.

PWC Jet Ski Cover (available in 3 sizes)

You ride your jet ski hard on the water. To make sure your watercraft performs up to its potential, it’s important to keep it covered between rides and during the off-season. The sun’s UV rays and the constant exposure to rain, snow, dew, and other moisture can damage your jet ski. A PWC cover can keep your watercraft clean, dry, and ready to ride at a moment’s notice.

Jet ski covers are available with a universal or custom fit. Custom covers offer a near perfect fit, but be prepared to pay the price. Universal and semi-custom covers are more affordable and offer an adjustable fit that provides superior protection for your ride.

In order to find the right size jet ski cover, make sure you get the right measurements for your watercraft. Measure from the front nose to the longest rear point for proper sizing. Then choose the cover that best fits the dimensions of your boat.

Jet Ski Cover Measurements

After rinsing the boat with fresh water, allow the boat to dry completely before installing the cover.

Using a boat cover around salt water is basically the same as using it around fresh water. In both cases, the boat cover needs to be cleaned regularly. Depending on the amount of salt to which your boat cover is exposed, it may need to be cleaned more often. Salt water leaves behind residue that attracts moisture, which can result in mildew.

After you rinse your boat with fresh water, allow it to dry completely before installing the boat cover. Since most saltwater areas are quite humid, it’s important to wait until the boat dries before covering it. Otherwise, mold and mildew will begin to grow on the cover.

Protect your jet ski with a breathable boat cover.

What Happens When Moisture Gets Trapped?

First, trapped water or condensation can damage the boat’s interior, including the bilge, hull, and fabric materials. Cushions tend to soak up moisture, creating ideal conditions for mold and mildew growth. If the cushions are removable, the best option is to remove the cushions and store them in a dry, protected indoor area.

Second, trapped moisture can damage the boat cover. Mold and mildew thrive in moist environments, and your boat cover is no exception. Mold growth will weaken the cover and compromise the protection that it provides for your boat or jet ski.

How Do I Make Sure My Boat Cover Can Breathe?

Even if the boat cover you purchase is clearly labeled as breathable, there are a few things you need to remember in order for the venting system to work properly.

First, throwing a tarp (or any other covering) over the boat cover will negate the venting system by trapping the moisture underneath the tarp. Do not put anything else on top of a breathable cover.

Second, keep the cover free of dirt and debris, which can plug up the breathable material and promote mold and mildew growth. Wash the cover as needed to keep it clean.

Finally, don’t allow pools of water to stand on the cover. They can compromise the water resistant properties of the cover, which leaves your boat vulnerable to moisture damage.

Take good care of your boat and your breathable cover, and your boat and cover will last for years to come!

The type of fabric used to make a boat cover or PWC cover affects how durable, breathable, and waterproof it will be. Not all boat covers are equal in quality. Below are some factors that affect the quality of a cover.

Type of Fabric

Boat cover made with marine-grade polyester fabric

1. Poly/Cotton Blend

The cheapest boat covers are made from a poly/cotton blend. This fabric breaks down faster and doesn’t protect the boat as well as other types of fabric. Covers made from a poly/cotton blend are typically only under warranty for a year and are only suitable for mild climates and minimal use.

2. Marine-Grade Polyester

Marine-grade polyester is a much more durable fabric than poly/cotton blend. These boat covers are slightly more expensive, but the durability is well worth the cost. Polyester boat covers offer an ideal balance of strong protection and cost effectiveness. They resist wear and tear and mildew growth much better than poly/cotton covers.

3. Acrylic

Acrylic boat covers are high end covers that offer superior protection; however, they are also more expensive to produce, which means that their cost is much higher than for other types of fabric.

Fabric Weight and Weave

In most cases, the heavier the fabric, the more durable it will be. However, durability is also affected by the tightness of the weave. A boat cover with a lighter weight and tighter weave may be more durable than a cover with a heavier weight but a coarser weave.

Fabric Color

Reds and yellows tend to fade the fastest. Blues seem to keep their color the longest. A UV protective coating will make the color last even longer.

When it comes time to cover up your jet ski, you want a quality cover that protects your boat and is strong enough to endure harsh weather.

What should you look for in a jet ski cover?

• Water repellent coating to keep your jet ski dry
• Vent system to promote air circulation and prevent mold and mildew growth or moisture damage
• Double-stitched seams to prevent leaking at the seams
• Storage bag to store your cover when not in use
• Marine-grade poly material that holds up under harsh weather and strong winds
• Elastic hem for a snug fit to keep the wind from billowing up the cover or tearing it out of place
• Tie-down straps to keep the jet ski cover in place
• A warranty and satisfaction guarantee to give you peace of mind

Looking for a quality jet ski cover that won’t break your budget? Check out the PWC Jet Ski Covers from DuraShield!